Ooni Koda 2 Regulator: Pressure, Hose and Leak Check
6 min read · by Hannah Cole · Last updated: November 15, 2026
The Ooni Koda 2 regulator sits between the propane cylinder and the hose, and it controls the gas pressure that reaches the burner. Ooni’s Koda 2 setup guidance includes a 28 mBar regulator, and the regulator and hose must be the Ooni-specified parts with a certification that matches the manual. Check the pressure rating and the tank connection type before you connect anything, and replace the regulator or hose at the first sign of damage.
What the regulator and hose do
A propane cylinder holds gas at a pressure higher than the oven is designed to use. The regulator reduces that pressure to a steady, fixed level, and the flexible hose carries the gas from the regulator to the oven’s gas inlet. Both parts have to match each other and the oven, so a regulator with the wrong pressure rating or a hose that does not seal can cause unsafe operation.

The Koda 2 setup guide says the included gas hose and 28 mBar regulator are to be connected to a propane gas tank. Ooni’s accessory listings for other regions show outlet pressures of 30 mbar, 37 mbar or 50 mbar, depending on the market. The pressure printed on the regulator must match what your oven is rated for, so read the manual for your region rather than assuming a number from another market.
Connecting the regulator to the tank
Regulators come in two tank-connection types: screw and push-on. Ooni’s Koda manuals describe the push-on type as pressed onto the tank valve until it locks, and the screw type as screwed in as far as it will go. Make sure the connection is seated before you open the tank valve. The tank side of the setup is explained in attaching a propane tank to the oven.
- Confirm the regulator’s pressure matches the manual for your region and that it is the Ooni part specified for the oven.
- Close the tank valve, then attach the regulator to the tank by the connection type shown above.
- Clip the hose to the oven’s gas inlet and tighten it according to the manual.
- Open the tank valve slowly and check every joint for leaks before lighting the oven.


Leak checks and hose safety
An older Koda manual advises a leak check on the hose and regulator connections using a soap and water solution before lighting the appliance. Brush the solution over each joint with the tank valve open. Bubbles mean gas is escaping, so close the valve, tighten the joint and test again. If the bubbles continue, do not light the oven; replace the part or contact Ooni support. A sister guide for the larger oven is the Koda 16 propane accessories page.
Inspect the hose before each use. Replace it if you see a cut, wear or abrasion, and keep it away from heated surfaces so the heat does not soften or damage it. The Koda 2 Pro manual requires a regulator certified to ANSI/UL 144 and a flexible hose as specified by the manufacturer. Replacement parts should be the ones Ooni specifies, not generic substitutes.
When to replace the regulator
Replace the regulator or hose if it is cracked, leaks at any joint, or shows damage after a knock or a fall. A gas smell near the oven is a stop sign: close the tank valve, move away from the oven, and do not light it. Once the area is ventilated and the leak is found and fixed, retest the connections with the soap solution before the next use. Tank size matters too, as covered in choosing a propane tank size.
Choosing the right regulator for a Koda 2
Start with the market. The pressure rating is set by region, so a regulator sold for one country may not match the oven you own. Check the manual for your region, then confirm the pressure printed on the regulator matches it before you buy or connect anything.
Next, check the tank valve. Push-on and screw regulators fit different valves, and forcing the wrong type can damage the threads or leave a gap that leaks. Look at the valve on your cylinder before ordering, and buy the type that seats on it without adapters.
Finally, prefer the Ooni-specified part. A universal regulator may fit the tank but not the hose connection or the pressure the oven was set for. If you are unsure, contact Ooni support with your oven model and region before buying, and keep the original packaging and paperwork in case a warranty claim is needed.
Before you light: a simple routine
Build a short routine and run it every time the oven is connected. Look at the regulator and hose for cracks, flattening or stiffness. Confirm the connection is seated and the valve is closed before you attach anything, then open the valve slowly and run the soap test on each joint. Only after the test shows no bubbles should you light the oven.
Disconnect the regulator and hose when the oven is not in use, and store the cylinder upright outdoors, away from heat and direct sun. Keep a note of the pressure rating and the connection type for your regulator, so that a replacement matches the original. If a joint keeps leaking after you tighten it, stop and replace the part rather than forcing the connection.
Frequently Asked Questions
What pressure is the Ooni Koda 2 regulator?
The Koda 2 setup guidance includes a 28 mBar regulator. Regional accessory listings show 30, 37 or 50 mbar options, so check the manual for your market and the rating printed on the regulator.
Can I use any propane regulator with the Koda 2?
No. Use a regulator certified to ANSI/UL 144 with the right pressure and tank connection, and use the flexible hose specified by Ooni. Ask Ooni support if you are unsure which part fits your oven.
How do I check the regulator for leaks?
Use a soap and water solution on each joint with the tank valve open. Bubbles show a leak. Close the valve, fix the joint, and check again before lighting.
Is a push-on or screw regulator better?
Neither is better in general. Choose the type that matches your tank valve. For push-on types, press until the regulator locks; for screw types, screw it in as far as it goes, and check for leaks either way.
Match the regulator to the manual’s pressure and tank type, use Ooni-specified parts, and leak-check every joint before lighting. Replace damaged parts without delay, and treat any gas smell as a reason to stop. Check the manual for your region before you connect anything.
10 min readGear & PantryOoni Koda 12 Regulator: What It Does, How to Check It, and What to BuyUpdated Nov 11, 2026
9 min readGear & PantryBest Table for the Ooni Koda 2 Max: What Fits and What to CheckUpdated Nov 11, 2026
9 min readGear & PantryBest Table for Ooni Koda 2: Which Options Fit and What to CheckUpdated Nov 11, 2026
8 min readGear & PantryOoni Koda 2 Pizza Stone: Best Replacement and 5 Fit ChecksUpdated Nov 10, 2026
9 min readGear & PantryOoni Koda 2 Pro Cover: Fit, Storage and What to Check Before You BuyUpdated Nov 10, 2026
8 min readGear & PantryBest Table for Ooni Koda 2 Pro: Which Options Fit and What to CheckUpdated Nov 10, 2026