Gozney Arc XL Temperature Guide for Pizza
7 min read · by Arjun Mehta · Last updated: November 7, 2026
The Gozney Arc XL temperature you should aim for depends on the pizza style you cook. Gozney’s technical manual lists working ranges from 320 to 480°C (608 to 896°F), with Neapolitan pizza at the top of the scale. The oven’s digital display shows the temperature from inside the oven, so read it before you launch a pizza.
What temperature range does the Gozney Arc XL manual recommend?
Gozney’s technical manual recommends 320 to 370°C for New York style, 370 to 430°C for Roman style and 430 to 480°C for Neapolitan pizza. Those are the only ranges the manual gives for pizza, so they are the best starting point for any Gozney Arc XL temperature target.

According to the Gozney Arc and Arc XL technical manual, the Neapolitan range is the hottest of the three, and anything above 480°C falls outside the chart. The table below converts each range to Fahrenheit for readers who prefer degrees F. Treat it as the planning chart for your Gozney Arc XL temperature: choose the pizza style first, then hold the flame so the reading stays inside that band.
| Pizza style | Manual range (°C) | Equivalent (°F) |
|---|---|---|
| New York | 320 to 370°C | 608 to 698°F |
| Roman | 370 to 430°C | 698 to 806°F |
| Neapolitan | 430 to 480°C | 806 to 896°F |
| Above the chart | Labelled “Over Temp (Too Hot)” | Above 896°F |
How do you read the Arc XL digital temperature display?
The Arc XL digital display shows the Gozney Arc XL temperature from inside the oven once its sensor is plugged in and the batteries are fitted. The manual describes the setup in these steps, and our Gozney Arc XL manual guide has the rest of the key points.

- Fit the batteries in the display.
- Remove the plastic cap from the sensor jack and push the jack fully into the socket on the rear of the display.
- Hold the power button down until the screen turns on.
- Place the display on the oven. It is held in place by magnets.
If the Gozney Arc XL temperature display shows error E1, the manual points to a loose jack or a damaged probe. Push the jack in fully first. If the error stays, the probe may need replacing, and the manual’s maintenance section covers that step.
How long does the Arc XL take to heat up, and what does the first firing involve?
The manual does not publish a heat-up time in minutes, so this guide does not give one. It does require a cure on the first firing, which means 30 minutes on a medium to low flame before you move to high.
After that first cure, the manual says you can bring the oven up to the desired temperature straight from ignition. If the oven has sat unused for a long time, cure it again as if it were new. Plan extra time on any bake day, because the stone needs to reach a steady Gozney Arc XL temperature before you cook.
A reviewer in Living Etc’s Arc XL review called the wait the main downside, writing that “the only drawback would be the time it takes to reach cooking temperature.” That matches the manual’s advice to start early and check the display rather than guess.
What happens if the Arc XL runs over 480°C?
Any Gozney Arc XL temperature reading above 480°C is labelled “Over Temp (Too Hot)” in the manual, and the display shows error E3 once the probe passes 700°C (1292°F). Treat any reading above the Neapolitan range as a sign to stop and check the flame.
- If E3 appears, turn the burner off and let the oven cool naturally.
- Do not try to cool the oven quickly, because the manual warns that rapid cooling can crack the stone floor.
- Damage from misuse of the stone or other parts is not covered by the warranty, according to the manual.
How do cold weather and the gas cylinder affect the temperature?
Below 0°C, the manual expects the gas cylinder to lose power, which can make the flame look small and slow the climb to any Gozney Arc XL temperature target. A small cylinder makes this worse, so the manual recommends a 5 kg canister as the minimum.
- Replace the cylinder if it is near empty, because the manual lists an empty canister as a possible cause of a small flame.
- On the first firing or after changing the cylinder, the gas can take up to 30 seconds to flow, so keep the control knob pressed for 30 seconds.
- If the flame goes out, turn off the control knob and the cylinder valve, then wait 5 minutes before relighting.
- If the burner makes a loud grumbling sound, turn it down to low and back to high. If the sound continues, turn the burner off for 5 minutes and retry the ignition.
- Use the oven outdoors only (see can you use a Gozney Arc indoors), and keep it at least 1.5 m from any structure, combustible material or other gas cylinder.
Wind affects the flame as well as the Gozney Arc XL temperature. The manual says to point the oven mouth away from the wind and to use wind breaks, because wind can blow the flame down into the dock. If you see fire coming from the dock, turn the oven off at the gas bottle or the control knob, and never operate the oven in high winds. Place it on a level, stable surface that can hold the 25 kg Arc XL; the Gozney Arc XL dimensions help you plan the space.
When you finish cooking, turn off the gas at the canister first so the burner uses up any gas left in the pipe. Three minutes later it is safe to remove the regulator and turn the control dial back to off. If you run the oven on a fixed supply instead of a cylinder, read about Gozney Arc XL natural gas first.
Frequently Asked Questions
What is the best Gozney Arc XL temperature for Neapolitan pizza?
The manual recommends 430 to 480°C for Neapolitan pizza, which is 806 to 896°F. That is the top of the working range, so aim for the middle of the band and check the display before you launch the pizza. For recipes paired with oven settings on the standard Arc, see Gozney Arc recipes and settings.
Is a Gozney Arc XL temperature above 480°C safe for cooking?
The manual labels readings above 480°C as “Over Temp (Too Hot)” and does not list them as a pizza range. If the display climbs there, stop and check the burner setting. Error E3 appears when the probe passes 700°C, and that needs the oven to cool naturally. Keep every Gozney Arc XL temperature reading below that point.
Why does the Gozney Arc XL temperature display show an error code?
The manual says E1 can be caused by a loose sensor jack or a damaged probe, so check the connection first. E3 means the probe has read above 700°C, which can damage the unit if the oven keeps running that hot.
How long should I cure a new Arc XL?
The manual recommends putting the burner on a medium to low flame for 30 minutes on the first firing. After that, move to a high flame. If the oven has been dormant for a long time, cure it again before cooking.
Can I use a small gas cylinder in winter?
The manual recommends a 5 kg canister as a minimum and warns that cylinder power drops below 0°C. The manual also lists a canister that is too small as a possible cause of a weak flame, so use a larger cylinder and keep it at a safe distance from the oven.
Start with the manual’s range for the pizza style you cook, and read the Gozney Arc XL temperature on the display before every bake instead of trusting the dial alone. If you cook in cold weather, plan for a weaker flame, a larger cylinder and a longer warm-up. Once the reading is steady, try the Gozney Arc XL recipes.
9 min readBy Use & ModelGozney Arc XL Recipes: What You Can Cook and the Settings Behind ThemUpdated Nov 7, 2026
9 min readBy Use & ModelGozney Arc XL Manual: How to Set Up, Light and Cure Your OvenUpdated Nov 7, 2026
9 min readBy Use & ModelGozney Arc XL Accessories: What Comes in the Box and What to BuyUpdated Nov 15, 2026
9 min readBy Use & ModelGozney Arc XL Natural Gas: What the Manual SaysUpdated Nov 7, 2026
9 min readBy Use & ModelGozney Arc XL Dimensions: Clearance, Weight and Space GuideUpdated Nov 7, 2026
8 min readBy Use & ModelHow to Clean Gozney Arc XL SafelyUpdated Nov 7, 2026