Ooni Koda 12 Won’t Light? Step-by-Step Fixes
8 min read · by Arjun Mehta · Last updated: November 10, 2026
If your Ooni Koda 12 won’t light, check the propane supply first, then relight with the manual’s knob sequence. Ooni’s Koda 12 Essentials Guide points to the tank, the regulator and the connections as the first places to look. The guide also asks you to wait before any relight and never to cook on a connection that fails a leak test.
Ooni Koda 12 Won’t Light? Start With the Propane Tank and Regulator
If your Ooni Koda 12 won’t light, confirm the propane tank is full and standing upright, then check that the regulator is secure before you try anything else.

The Ooni Koda 12 Essentials Guide asks you to check the tank, hose and regulator before every cook. Lighting problems often start at the tank end, so begin there.
- Make sure the gas tank is full and in an upright position.
- Clear any debris from the regulator and tank connections, then reattach the regulator.
- Disconnect the regulator from the tank for 5 minutes. The guide describes this as a reset for a regulator whose safety may have tripped.
- On a twist-open gas bottle (US), open the gas flow very slowly. The guide warns that a sudden surge can trip the regulator’s safety feature.
Work through these four items in order before you move on to the burner. If your Ooni Koda 12 won’t light even with a full tank, the connections are the next suspect. For the usual lighting steps, see how to use the Ooni Koda 12.
Run a Leak Test Before You Light
A leak test on the connections is the check to do before every use, because bubbles mean gas is escaping at a fitting or in the hose.
Apply a leak detector spray or a soapy water solution to the connections between the propane tank and the oven, and to the hose. The guide asks for this check before every use, not only when the oven fails to light.
If you see bubbles, switch off the gas supply immediately and check the fittings again. If bubbles continue, switch off the gas and service the regulator. The guide says never to cook with a product that has failed a leak test, and to contact support for further advice.
When Your Ooni Koda 12 Won’t Light: The Right Knob Sequence
Push the control knob in, then turn it slowly counter-clockwise from 12 to 9 o’clock, taking at least three seconds so the gas can flow before the spark ignites it.

- Confirm the gas supply is on and the leak test passed.
- Push the control knob in.
- Turn it slowly counter-clockwise from 12 to 9 o’clock. The guide says this should take at least three seconds.
- You should hear the gas flowing before the dial reaches 9 o’clock, which is where the spark starts.
- Keep the knob pushed in after ignition. The guide gives two times: 5 seconds on its quick start page and 20 seconds in the troubleshooting section. Follow the lighting section of your own manual and hold the knob in for the longer time if you are unsure.
If your Ooni Koda 12 won’t light on the first try, do not panic: lighting can take more than one attempt. The guide says the number of tries depends on how long the oven has been unused, the ambient temperature and your gas set-up. If the flame goes out, wait 5 minutes before relighting.
Do not look directly into the oven opening while lighting, because flames may escape during the first firing. If there is wind, make sure it enters the back of the oven, as the guide advises.
Ooni Koda 12 Won’t Light or Stay Lit: Flame Safety Device
The Flame Safety Device cuts off the gas when the thermocouple does not read a high enough temperature, so a dirty thermocouple can stop the oven from staying lit.
The guide explains the logic in plain terms: the oven thinks there is no flame, so it does not let gas flow. That is why the knob must be held for the full sequence after ignition.
If your Ooni Koda 12 won’t light for long enough to heat the stone, the thermocouple is a likely cause. To clean it, wipe it with a dry paper towel. If you cannot reach it, the guide says to use compressed air and give it a good blast to clear it. If you own the larger Koda 16, see Koda 16 lighting fixes for its step-by-step checks.
Symptom Table: Match the Problem to the Fix
Match the sound, flame or behaviour you see to the first action in the table below, and work down the list only if that action does not solve it.
| Symptom | What the guide says | First action |
|---|---|---|
| Won’t light | Lighting needs a slow turn and may take several attempts | Check the tank, reset the regulator for 5 minutes, then repeat the slow sequence |
| Roaring sound from the burner | The burner has not ignited correctly and may overheat the oven | Switch off and wait 5 minutes before relighting |
| Flame goes out when you release the knob | The Flame Safety Device cuts gas if the thermocouple reads too cool | Wipe the thermocouple with a dry paper towel, then relight after 5 minutes |
| Asymmetrical flame | There may be a blockage in the burner | Clean the burner with compressed air |
| Flame too low | The guide recommends checking the gas tank levels | Check the tank fill level and the connections |
| Smell of gas | Gas may be leaking at a connection | Turn off the tank valve and follow the gas smell steps below |
Use the table as a checklist rather than a diagnosis. If none of these actions fixes the problem, the next step is to contact support. Owners of the larger oven can also read about problems with the Ooni Koda 16.
What to Do If You Smell Gas
If you smell gas, turn off the gas valve on the tank, put out any open flames and keep a safe distance from the oven.
- Turn off the gas supply by closing the valve on the propane tank.
- Extinguish any open flame and do not try to light the oven again.
- If the smell persists, keep your distance and contact your local fire department.
Do not relight until you have found the source and the leak test passes. The guide is clear on this point, and a gas smell is not something to troubleshoot with repeated attempts.
When to Stop and Contact Ooni Support
If your Ooni Koda 12 won’t light after the steps above, or the leak test shows bubbles after you have checked the fittings, contact Ooni support.
The guide points to support.ooni.com for further troubleshooting. You can also find Ooni’s help centre at Ooni’s help centre page.
What This Guide Does Not Verify
The Essentials Guide does not list error codes, a battery or igniter replacement procedure, or a specific part-by-part ignition test, so this article does not describe any of them. Once it lights, the Ooni Koda 12 heat-up time guide explains what to expect, and the Ooni Koda 12 cleaning steps help keep the burner clear.
To check which gas rating your oven uses, look at the regulator and the operational manual that came with the oven. The guide’s flame guidance covers propane models rated at 28, 37 and 50 mbar, and a 30 mbar butane variant, so the rating matters when you read it. Natural gas owners should read the Ooni Koda 12 natural gas guide instead, since this one covers propane.
Frequently Asked Questions
What should I do if my Ooni Koda 12 won’t light?
Check the tank and regulator first, then run the leak test and repeat the slow knob sequence. If it still won’t light, the guide points to support.ooni.com rather than more attempts.
How long should I wait before relighting the Koda 12?
Wait 5 minutes after the flame goes out before you relight, as the guide advises. Switch off the gas supply at the tank first if you notice any gas smell or hissing.
Is a roaring sound from the burner normal?
No. The guide says the oven runs quietly when lit, and a louder roar means the gas burner has not ignited correctly. Switch off for 5 minutes and relight, because incorrect lighting may cause overheating and damage.
Can I still cook if the leak test shows bubbles?
No. The guide says never to cook with a product that has failed a leak test. Check the fittings, and if the bubbles continue, switch off the gas and contact support.
What does a long sooty yellow flame mean?
The guide says that flame appears when butane is used in a propane model, and it recommends using propane only in those models. Check which gas your tank holds before you light the oven again.
Why do I have to hold the knob after it lights?
The Flame Safety Device cuts off the gas if the thermocouple does not read a high enough temperature. The guide gives 5 seconds on its quick start page and 20 seconds in its troubleshooting section, so follow the lighting section of your manual.
Work through the checks in order when your Ooni Koda 12 won’t light: tank, leak test, slow knob sequence, then the thermocouple. If the gas smells or the leak test fails, stop and contact support rather than trying more attempts.
8 min readBy Use & ModelOoni Koda 16 Won’t Light? Fix It Step by StepUpdated Nov 10, 2026
9 min readBy Use & ModelGozney Dome Won’t Light? Check the Battery, Gas Flow and BurnerUpdated Nov 10, 2026
9 min readBy Use & ModelHow to Clean Ooni Koda 12 in 4 Easy StepsUpdated Nov 7, 2026
7 min readBy Use & ModelOoni Karu 12 Charcoal: How to Light and Cook With Lump CharcoalUpdated Nov 8, 2026
9 min readBy Use & ModelOoni Karu 12 Recipes: Simple Dough Weights and Oven StepsUpdated Nov 8, 2026
9 min readBy Use & ModelOoni Fyra 12 Manual: Setup, Lighting and Cool-Down StepsUpdated Nov 6, 2026