Gozney Dome Won’t Light? Check the Battery, Gas Flow and Burner
9 min read · by Arjun Mehta · Last updated: November 10, 2026
If your Gozney Dome won’t light, the cause is usually one of three things: an empty ignition battery, no gas reaching the pilot, or a blocked burner or venturi. Check them in that order before you call support. Gozney’s Dome Technical Manual (DOC-0528-03) describes these checks for gas models, and the exact steps depend on your model and the gas type on the data plate. If you smell gas at any point, stop and follow the gas safety steps in the last section.
Gozney Dome Won’t Light: Check the Gas Supply First
Before you touch the ignition, confirm that gas can actually reach the burner. A cylinder that is empty or nearly empty is one of the first causes the manual lists for both failure to ignite and a weak flame.
Gozney recommends a 28 lb gas bottle with Dome, and says never to fill a cylinder beyond 80 percent. Work through these checks:
- Make sure the gas type matches the data plate page, because the manual lists separate settings for LPG and natural gas. Our Gozney Dome natural gas guide covers the natural gas side.
- Confirm the cylinder is not near empty. Swap in a full cylinder to rule it out.
- Check the regulator. The manual says to insert the black QCC1 regulator nipple onto the fuel valve and hand tighten it clockwise, without tools.
- Leak test every joint with soapy water. If a joint bubbles, it leaks. The manual requires a leak test before first use, after every refill, and each time the cylinder is hooked up.
Never light the burners while you leak check. The manual warns about this directly, so turn the control knob off and make sure the gas valve is closed during the test. Cold weather also matters: the manual says that when the ambient temperature drops below 0 °C, a loss of power from the gas canister is expected.
Gozney Dome Won’t Light: Check the Ignition Battery
If your Gozney Dome won’t light and the control knob does not click when you press it, the ignition battery is the first thing to check. The manual lists an empty ignition battery as a cause of failure to ignite and says to replace the battery at the back of the unit if the knob makes no clicking sound.
The battery is one AAA cell that sits in the ignition module behind the rear dock panel. To replace it, remove the rear panel on the dock, unscrew the cap on the module, and place a fresh AAA battery in with the negative end first. Put the cap and panel back on. The manual describes this step in its first-use setup, and it applies whenever the battery needs replacing.
A fresh battery is a quick check, so do this before you assume a gas or burner fault. If the knob still does not click with a new battery, the problem is more likely in the gas path or the burner, and the next sections cover those.
Gozney Dome Won’t Light? Pilot Light Steps
Lighting a Dome is a two-stage process: first the pilot, then the burner. If your Gozney Dome won’t light at the pilot stage, the burner will not light either.
Follow the manual’s sequence in the official Gozney Dome Technical Manual:
- Confirm the cylinder valve is open and the regulator is connected.
- Press the control knob in until you hear a constant clicking sound.
- Keep pressing, turn the knob 90 degrees, and hold it there until the pilot light is lit.
- Check for the pilot. You may not see a naked flame, but there should be clear reflections of it on the inside sides of the oven.
- Once the pilot is lit, turn the control dial counter-clockwise. The burner should light.
On first firing, or after you change a gas cylinder, the gas can take longer to reach the pilot. The manual says the burner can take up to 30 seconds for gas to flow through the system, and you should keep the control knob pressed until the pilot has ignited. Do not release the knob early and assume the unit has failed. The Gozney Dome manual walkthrough lists the same steps with the first-use setup.
Gozney Dome Won’t Light Because of a Blocked Burner?
A blocked burner or venturi stops gas from flowing properly, and the manual lists it as a cause of both failure to ignite and a weak flame. Blockages can be food residue or insect nests, so check before every fire-up.
The manual asks you to check the oven, burner and venturi for blockages before use, and to look inside the burner tube for insects before each fire-up. Wasps, bees and ants can nest there, and the manual says a clogged tube can lead to a fire beneath the oven, so an insect nest must be cleared out thoroughly.
To clean the venturi, wait until the oven is turned off and cool, then remove the maintenance hatch and use a vacuum cleaner with a long plastic nose to remove debris. The manual also says to check inside the dock for debris regularly. If the flame looks overly yellow or the burner is noisier than usual, the manual links that to debris blocking the venturi.
For general soot and stone care, Gozney’s academy has a separate cleaning guide. It covers the burn-off and stone steps, which are different from clearing the venturi. Our own Gozney Dome cleaning guide adds routine care.
Fix a Weak or Noisy Flame
A weak flame usually points to the fuel supply or cold weather, while a noisy flame usually points to debris in the burner. The table below sums up the manual’s troubleshooting guidance for the gas burner.

| Problem | Possible reasons | What the manual suggests |
|---|---|---|
| Flame looks too small | Near-empty cylinder, cylinder too small, ambient below 0 °C, blocked burner | Replace an empty cylinder. The manual recommends a 9 kg canister as a minimum. Expect less output below 0 °C. Clean the burner. |
| Failure to ignite | Ignition battery empty, blocked burner, gas canister empty | Keep the knob pressed until the pilot lights, since gas can take up to 30 seconds to flow. Replace the battery at the back if there is no click. Clear any blockage. |
| Noisy flame | Incorrect ignition, blocked burner | Turn the burner down to low, then back to high. If the noise continues, turn it off for 5 minutes and retry. If it persists, clean the debris from the burner. |
The manual also says that if the problem persists after these steps, you should contact Gozney for further support.
Relight Safely and Shut Down Correctly
Wait 5 minutes before you try to relight after the flame has gone out, and always turn the gas off at the cylinder before you switch the oven off.
- If the flame goes out, turn the control knob off and close the cylinder valve, then wait 5 minutes before relighting.
- To shut down after cooking, turn the gas off at the cylinder first so any gas left in the burner or pipe is used up safely.
- Wait 3 minutes after turning the gas off, then remove the regulator and turn the control dial back to off.
- If you smell gas, shut off the gas at the cylinder, turn off the switch on Dome, and put out any open flames. If the smell continues, move away from the oven and the gas supply, then call your gas supplier or the fire service.
The manual also warns against using flammable liquids to start or boost a fire in the oven, and says to keep such liquids well away while it is in use.
Smoking and Other Causes the Manual Does Not Cover
The manual does not describe smoking as a fault, so the cause of smoke is not confirmed here. Do not guess at the cause.
What the manual does confirm is that a normal flame is yellow and rolls along the top of the oven. A flame that is overly yellow, or a burner that is noisier than usual, is the manual’s sign of debris in the venturi, so start with the burner and dock checks above. For normal heat ranges once it lights, see the Gozney Dome temperature guide.
Things we could not confirm from the sources read for this article: the exact causes of smoke on your model, and any model-specific fixes. To check these, use the owner’s manual that came with your unit, match the model and gas type to the data plate page, and contact Gozney if the problem continues after the steps above. If the problem is smoke rather than a failed ignition, see our Gozney Dome smoking troubleshooting guide.

Frequently Asked Questions
Gozney Dome won’t light after I changed the gas bottle: why?
After a cylinder change, gas can take longer to reach the pilot. The manual says the burner can take up to 30 seconds for gas to flow, so keep the control knob pressed until the pilot lights.
How long should I wait before trying to relight?
If your Gozney Dome won’t light after a failed attempt, the manual says to turn the control knob and the cylinder valve off, then wait 5 minutes before attempting to relight the appliance.
Is a yellow flame normal?
Yes. The manual says the flame should be yellow and roll along the top of the oven. A flame that is overly yellow, or noisier than usual, suggests debris blocking the venturi.
Does cold weather affect ignition?
It can. The manual says that when the ambient temperature is below 0 °C, a loss of power from the gas canister is expected, which can make the flame look too small.
When should I contact Gozney?
Contact Gozney if the problem persists after you have checked the gas supply, the ignition battery, the pilot steps and the burner. The manual gives this as the final step in its troubleshooting table.
Work through the gas supply, the ignition battery, the pilot steps and the burner before you assume a fault. Keep the gas off and call Gozney if your Gozney Dome won’t light after these checks, and have your model and data plate details ready.
8 min readBy Use & ModelOoni Koda 16 Won’t Light? Fix It Step by StepUpdated Nov 10, 2026
8 min readBy Use & ModelOoni Koda 12 Won’t Light? Step-by-Step FixesUpdated Nov 10, 2026
9 min readBy Use & ModelOoni Karu 2 Accessories: Gas Burner, Fuel and Fit ChecksUpdated Nov 15, 2026
8 min readBy Use & ModelGozney Dome S1 Manual: Gas Setup, Leak Test and First FiringUpdated Nov 6, 2026
7 min readBy Use & ModelGozney Dome S1 Natural Gas: What the Manual Says and What It Does NotUpdated Nov 7, 2026
9 min readBy Use & ModelGozney Dome S1 Dimensions: Outside Size, Clearance and Gas SetupUpdated Nov 7, 2026