Solo Stove Pi Stand: Pi 12 Fit, Size and Checks Before You Buy
9 min read · by Hannah Cole · Last updated: November 17, 2026
The Solo Stove Pi stand is a steel cart for the Pi pizza oven, and the official manual says it is for the Pi 12 only. Check your oven model, the floor and the propane setup before you order one. This guide covers fit, size, assembly and the safety rules from the manual.
The stand gives the oven a rolling base with shelves and a propane tank holder. It suits a flat outdoor patio, and it is the wrong buy if your oven is not a Pi 12.
| Pick | Best for | Key fact |
|---|---|---|
| Official Solo Stove Pi stand | Pi 12 owners who want a matched cart | The manual says use only with the Pi 12 |
| Any other table or cart | Owners of other ovens, after a fit check | Must match your oven model, load limit and heat rules |
Solo Stove Pizza Oven Cart for Outdoor Pi Pizza
- Solo Stove
- 43 lb
Pros & ConsViewHide
Reasons to buy
- Made by Solo Stove for Pi pizza ovens
- Locking wheels and fold-down shelves
- Hidden spot for the propane tank
Reasons to avoid
- Listing says it fits the entire Pi family while the manual names only the Pi 12, so confirm with Solo Stove
- About 43 lb per the listing, so plan the spot on your patio first
What the Solo Stove Pi Stand Is
The Solo Stove Pi stand is a powder-coated steel cart with four locking casters, two side shelves and a propane tank base. The manual limits it to outdoor residential use.

Reviewed describes the frame as powder-coated steel with 360 degree caster wheels that lock. The cart also has a propane tank storage shelf, two side shelves and an underneath shelf. On the solo stove pi stand, the Solo Stove Pi pizza oven nests into the frame rather than locking in place, so you can lift it out for transport.
- Four casters with locks for moving and parking
- Two side shelves for ingredients and tools
- An underneath shelf for extra storage
- A propane tank base sized for a barbecue-style tank
- Outdoor residential use only, according to the manual

Does the Solo Stove Pi Stand Fit Your Oven?
The official manual says the stand is for the Solo Stove Pi 12 Pizza Oven only, so confirm your model before you order.
The product box above shows Solo Stove’s own cart, the official Solo Stove Pi stand, and its Amazon listing says it is compatible with the entire Pi family, so the listing and the manual do not agree. The manual’s first usage rule reads: “Use only with Solo Stove Pi 12 Pizza Oven.” Some retailer listings use titles such as “Solo Stove Stand for the Pi 20-Inch” oven. Those titles conflict with the manual, so the manual is the safer guide until Solo Stove confirms otherwise.
| Oven | Fit per manual | What to do |
|---|---|---|
| Solo Stove Pi 12 | Named in the manual | Confirm the model on the oven before ordering |
| Solo Stove Pi 20 | Not named in the manual; some listings say it fits | Ask Solo Stove support before buying |
| Any other oven | Not named | Run the fit checks in the table further down |
Look for the model name on the oven body and on the box before you buy the solo stove pi stand. If you cannot confirm the model, hold off on the stand until you can. Owners of the Pi Prime can read our Solo Stove Pi Prime guide and ask Solo Stove about fit.
Size, Weight and Layout
The assembled stand measures about 38.1 inches tall, 47.3 inches long and 35 inches wide, and weighs 45 pounds. The Prime sits differently, and a table for the taller Pi Prime explains how.
| Attribute | Value | Source |
|---|---|---|
| Height | About 38.1 in | Reviewed review |
| Length | About 47.3 in | Reviewed review |
| Width | About 35 in | Reviewed review |
| Weight | 45 lb (20.41 kg) | Reviewed review |
| Shelf load | About 10 lb (5 kg) per shelf | Solo Stove manual |
| Casters | Four, with locks | Reviewed review |
These figures for the solo stove pi stand come from a single review and the manual, and the Amazon listing for Solo Stove’s cart gives a slightly different height and weight, so treat all of them as approximate. Measure your patio and the path to it before you order, since the stand has to roll over the ground to reach the spot you want. Read the full set of specs in the Reviewed review of the Solo Stove Pizza Oven before you commit.
Assembly Before the First Cook
Assembling the solo stove pi stand takes 44 M6x20 screws with washers, a #2 Phillips screwdriver and the caster wrench included in the box.
Assemble the stand on a flat, level surface. The manual recommends leaving the screws loose until the frame is complete, because some parts need to shift during alignment. Start every fastener by hand or with hand tools, since the manual warns that power tools can cross-thread or strip them.
- Insert each crossmember into its bracket, then repeat for the remaining crossmembers.
- Align the propane tank base as the manual shows and fasten it with four screws and washers.
- Fasten the casters to the lower legs with the caster wrench included in the box.
- Follow the remaining steps in the manual for the shelves and the tank holder, then tighten every fastener.
Check the parts against the unpacking page before you start. If a part is damaged or missing, stop and contact Solo Stove customer service using the number listed in the manual rather than forcing the fit.
Safe Use on the Floor
Use the solo stove pi stand only on level, stable ground, with all wheels locked unless you are moving it.

The manual says not to use the stand on inclines, uneven ground, loose material, wet surfaces, vehicles, boats or stairs. It also warns that expansion joints, changes in the surface and outdoor rugs can catch the wheels and tip the stand. Those are common patio hazards, so walk the route before you roll the oven onto it. Once it is parked, a pizza oven cover keeps weather off the oven.
- Keep all casters locked while the oven is in use.
- Move the stand by the hand locations on either shelf, not by pushing or pulling the oven.
- Do not move the stand while the oven is in use or still warm.
- Keep loads light, since each shelf is meant to hold about 10 lb (5 kg).
- Use heat protection such as heat resistant gloves for hot items taken from the oven, and do not set them directly on the shelves.
Propane Tank and Setup
The solo stove pi stand takes a 20 lb propane barbecue-style tank with a QCC-1 connection, and the tank must sit on its base and be secured with the retaining bolt.
The manual says to use only tanks that conform to US Department of Transportation or CAN/CSA B339 standards. Seat the tank fully and rotate it so the retaining bolt lines up with the hole in the base of the tank. Then secure the bolt through that hole so the tank cannot come out.
- Use a 20 lb barbecue-style tank with a QCC-1 connection.
- Confirm the tank meets the DOT or CAN/CSA B339 standard before use.
- Secure the tank with the retaining bolt before you light the oven.
- Point the tank regulator toward the rear of the stand, as the manual’s setup page shows.
Follow the tank and connection instructions in the manual before the first cook. This guide does not replace the manual, and it does not cover gas-line work.
Stand or Another Table: a Checklist
Choose another table only when it matches your oven model, load limit, floor and heat rules, since the official solo stove pi stand is the simplest match for a Pi 12.
Skip the official stand if you own a different oven or if your patio slopes. Our guide to pizza oven tables compares options beyond the Solo Stove Pi stand. Skip any other table that fails one of the checks below, even if it looks sturdy.
| Criterion | What to check | Why it matters |
|---|---|---|
| Oven fit | A named model or footprint that matches your oven | The manual names only the Pi 12 for this stand |
| Load rating | A stated limit that covers the oven and fuel | The manual warns against overloading shelves |
| Level and locking | Lockable casters on level, stable ground | Uneven ground and rugs can tip a rolling base |
| Heat | Clearance and a heat-safe place for hot items | The manual warns the stand can get hot in use |
| Tank support | A secure spot for a 20 lb propane tank | The tank must be secured with its retaining bolt |
An unrated table is a poor swap for an oven, even when it looks solid. If you cannot find the load and heat details for a table, treat it as a no until you can.
Warranty and Support
According to the manual, Solo Stove covers each product against manufacturing defects and will replace, at its option, a genuine product sold by an authorized retailer that is deemed defective. It does not cover normal wear or misuse. If misuse makes a product unrepairable, the manual describes a one-time courtesy offer of 50% off a new product. Warranty claims for the solo stove pi stand do not apply outside the US and Canada.
Frequently Asked Questions
Does the Solo Stove Pi stand fit the Pi 20?
The official manual says the solo stove pi stand is for the Pi 12 only. Some retailer listings describe a fit with the 20-inch Pi, so confirm the oven model with Solo Stove before you order.
How much does the Solo Stove Pi stand weigh?
The Reviewed review lists the assembled stand at 45 lb (20.41 kg). Check that weight against your floor and the path you will roll it along.
Can I roll the stand while the oven is hot?
No. The manual says not to move the stand while the oven is in use or still warm. Let the oven cool and clear the shelves first.
What propane tank does the stand use?
The manual specifies a 20 lb barbecue-style tank with a QCC-1 connection. The tank must meet US DOT or CAN/CSA B339 standards and be secured with the retaining bolt.
Is the stand covered by warranty?
Solo Stove covers manufacturing defects. Normal wear and misuse are not covered, and claims apply only in the US and Canada, according to the manual.
Buy the solo stove pi stand only after you confirm that you own a Pi 12, that you have a level patio, and that you have room for a 20 lb propane tank. If any of those is missing, check another option against the checklist above.
9 min readGear & PantryBest Cover for Solo Stove Pi: Fit, Safety and Storage ChecksUpdated Nov 11, 2026
6 min readGear & PantrySolo Stove Pi Prime Stand: How to Choose the Right TableUpdated Nov 15, 2026
8 min readGear & PantryGozney Arc Stand: Size, Weight and Table Checks Before You BuyUpdated Nov 17, 2026
8 min readGear & PantryOoni Fyra 12 Cover: What Fits and What to Check Before You BuyUpdated Nov 11, 2026
9 min readGear & PantryGozney Arc XL Stand: What to Check Before You BuyUpdated Nov 8, 2026
9 min readGear & PantryGozney Dome Stand: What to Check Before You Buy a TableUpdated Nov 17, 2026