Hamilton Beach Pasta Maker Discs: The Seven Shapes and How to Swap Them
8 min read · by Arjun Mehta · Last updated: November 8, 2026
The hamilton beach pasta maker discs are seven shaping discs listed in the official Use and Care guide: Angel Hair, Spaghetti, Thick Spaghetti, Penne, Fettuccine, Wide Noodle and Lasagna. Each disc sets the shape of the pasta as it leaves the machine.
Two of the discs, Penne and Lasagna, are two-piece designs. The manual says never to run the machine without a disc in position, so check each fit before you plug the unit in. Our Hamilton Beach pasta maker manual guide covers the rest of the booklet.
Which Hamilton Beach Pasta Maker Discs Come With the Machine
The Hamilton Beach Electric Pasta Maker ships with seven shaping discs. The official Use and Care guide shows all of them in its parts diagram, so you can compare the names printed in the manual with the discs in your box.
The model is listed by retailers as 86650. Read the model number on the base or the box before you search for replacement parts, because a part listed for another Hamilton Beach pasta maker may not fit these Hamilton Beach pasta maker discs.
You can read the full parts list and safety rules in the Hamilton Beach Use and Care booklet. The English section starts on page 2 of the PDF, and the same file also holds the French and Spanish editions.
The Seven Shaping Discs and What Each One Makes
Five of the seven discs are single pieces, and only Penne and Lasagna are marked as two-piece discs in the manual. Pick the Hamilton Beach pasta maker discs that match the shape you want, then check the design before you assemble the machine.

| Disc name in the manual | Piece design | Shape it is named for |
|---|---|---|
| Angel Hair | One piece | Very thin strands |
| Spaghetti | One piece | Long, round strands |
| Thick Spaghetti | One piece | Wider round strands |
| Penne (2-Piece Disc) | Two pieces | Short tubes |
| Fettuccine | One piece | Flat ribbons |
| Wide Noodle | One piece | Wider flat noodles |
| Lasagna (2-Piece Disc) | Two pieces | Wide flat sheets |
The table uses the manual’s disc names. Shape descriptions are general guides, not model-specific measurements, because the manual does not give dimensions for each disc.
Keep the Hamilton Beach pasta maker discs for the shapes you cook most often in the storage drawer, and do not run the machine with a disc missing. The manual lists this as a rule for every batch.
How to Fit and Remove a Shaping Disc
You fit a Hamilton Beach pasta maker disc by aligning its ribs with the barrel, then holding it in place while you lock the collar. Unplug the machine first, then follow the steps in the order the manual gives.
- Unplug the machine, then insert the extruder small end first into the barrel end of the mixing bowl.
- Choose the shaping disc and position it on the barrel end, aligning the ribs on the barrel with the features on the disc.
- Hold the disc in place and secure the collar by turning it clockwise.
- Plug the machine in, then add the dry ingredients and select the program you want.
The ribs on the barrel stop each of the Hamilton Beach pasta maker discs from turning during extrusion, so check that the disc cannot turn before you press start.
The Quick Pasta program takes 15 to 18 minutes and the Pasta program takes 20 to 30 minutes. Both extrude the pasta through the disc automatically, while the manual mode stops kneading after 5 minutes and waits for you to press Extrude Pasta.
Cleaning, Storing and Removing a Stuck Disc
Clean each Hamilton Beach pasta maker disc after the dough has dried, then store it in the drawer at the bottom of the base. The manual gives a fixed order for removal and cleaning.

- Unplug the machine, turn the collar counterclockwise, then remove the shaping disc.
- Use the cleaning tool to poke out any dough left in the holes of the disc.
- If dough will not come out, place the disc in the freezer for 30 to 60 minutes, then try again.
- Wash the removable parts in hot, soapy water, rinse and dry them, or place them on the top rack of the dishwasher.
- Store the Hamilton Beach pasta maker discs in the storage drawer at the bottom of the base.
Cleaning rules are the same for every one of the Hamilton Beach pasta maker discs. Dough is easier to remove when it is dry. The manual suggests letting the dough dry before you use the cleaning tool. Wipe the base with a soft damp cloth and dry it, but never immerse the base or the cord in water. For habits that apply to any extruder, see our guide to cleaning a pasta machine.
Can You Buy Extra Hamilton Beach Pasta Maker Discs?
This guide did not confirm that single replacement Hamilton Beach pasta maker discs are sold for the model. The manual says parts are ordered through the Hamilton Beach website for the US, but it does not list a disc price or a part number for each disc.
A retailer listing for the model says new units are no longer available, which suggests a replacement disc may be hard to find new. Contact Hamilton Beach customer service with the model number before you plan a recipe around one specific disc, and see our Hamilton Beach pasta maker recipes for dough ideas that work with the discs you have.
Dough Consistency for Hamilton Beach Pasta Maker Discs
The Hamilton Beach manual describes the right dough as moist and crumbly, not a solid mass. It says the dough will look drier than handmade dough but should form a tight consistency once it is extruded. That matters for Hamilton Beach pasta maker discs, because the dough has to be moist enough to pass through the disc but firm enough to hold its shape.
If the dough is too dry, the manual says to add 5 ml (one teaspoon) of liquid, wait 15 seconds for it to mix in, and repeat if needed. If it is too wet, press START/STOP and unplug the machine, break up any clumps by hand, and add 2 tablespoons (30 ml) of flour. Replace the lid, plug the machine back in, press KNEAD DOUGH and then START/STOP, and repeat as needed.
The first part of each extrusion can look dry, and the manual says that is normal. As the mixing paddle keeps working, the dough becomes more pliable. If you want a cleaner start, trim off the first inch and discard it.
Storing Fresh Pasta Made With the Discs
The manual gives clear storage limits for pasta made with Hamilton Beach pasta maker discs. Cook the pasta immediately, store it in an airtight container in the refrigerator for up to 3 days, or place it in a freezer-safe container in the freezer for up to 3 months. To cook it, use salted boiling water until the pasta floats, then check for doneness.
Fresh pasta dries out quickly once it leaves the disc, so cut it to length as it extrudes and move it to its storage container without delay. Keep leftover pasta covered, since the manual's recipes say to wrap and store unused pasta.
Safety Checks Before Each Run
The Hamilton Beach manual lists several rules that apply every time you swap Hamilton Beach pasta maker discs. Keep these in mind before you press start, since most of them are simple to skip in a hurry.
- Run the machine only with a shaping disc in position, and make sure the pasta maker is fully assembled before you turn it on.
- Do not leave the machine unattended while it is running.
- Do not use the appliance if the mixing paddle, extruder, shaping disc, collar or any part of the mixing bowl is damaged.
- Use the machine on a dry, level surface, and do not use it outdoors.
- Unplug the machine before removing or cleaning any part, and never immerse the cord, plug or base in water.
Frequently Asked Questions
Can I use a disc from another pasta maker brand?
The manual does not list third-party Hamilton Beach pasta maker discs as compatible, so treat them as unconfirmed. Check the disc design and the collar fit on your machine before you use a part from another brand, and do not run the machine if a disc does not sit fully in place.
Can I run the pasta maker without a disc?
No. The manual says not to operate the pasta maker without a shaping disc in position, and to make sure the machine is fully assembled before the motor turns on.
How long does a pasta program take?
The Quick Pasta program takes 15 to 18 minutes, and the Pasta program takes 20 to 30 minutes. Both programs extrude through the disc you installed and stop when they finish. Compare the full machine in our Hamilton Beach pasta machine overview.
What dough ratio does the guide give?
The simple pasta recipe uses 400 g of all-purpose flour and 135 ml of liquid for about 1 pound of pasta. The manual says other flours and liquids change the ratio, so adjust the liquid slowly.
Match the Hamilton Beach pasta maker discs to the shape you want, check the collar before you plug in, and clean the disc once the dough has dried. If a disc is missing, contact Hamilton Beach customer service before you plan the batch.
9 min readBy Use & ModelHamilton Beach Pasta Maker Manual: Model 86650 GuideUpdated Nov 7, 2026
9 min readBy Use & ModelHamilton Beach Pasta Maker Recipes: 4 Simple Doughs for 2026Updated Nov 7, 2026
9 min readBy Use & ModelPhilips 7000 Pasta Maker Discs: What Comes in the Box and How to Clean ThemUpdated Nov 15, 2026
8 min readBy Use & ModelPhilips Viva Pasta Maker Discs: What Comes in the Box and What to CheckUpdated Nov 10, 2026
8 min readBy Use & ModelPhilips 7000 Pasta Maker Recipes: Where to Find ThemUpdated Nov 8, 2026
8 min readBy Use & ModelMarcato Atlas 150 Attachments: Which Cutter Shapes FitUpdated Nov 8, 2026