Solo Stove Pi Gas Burner: Specs, Propane Setup and Safe Use
9 min read · by Arjun Mehta · Last updated: November 8, 2026
The Solo Stove Pi gas burner is a propane accessory that replaces the wood-burning assembly in the Solo Stove Pi pizza oven. The manufacturer rates it at 15,000 BTU/hr and approves it for propane only. It is outdoor equipment that produces carbon monoxide, so the cylinder and clearance rules matter as much as the output figure.
What the Solo Stove Pi gas burner replaces and how it fits
The Solo Stove Pi gas burner installs in the space of the wood-burning assembly, after you remove the wood access door, the fuel grate and the ash pan. The manual treats this as a parts swap, not a modification of the oven. For the wood setup you are replacing, see Solo Stove Pi instructions.

Clean out the ash pan before you install the burner, because the manual asks for that first. Inspect the burner for damage when you unpack it. Then remove the thumbscrews from their storage spot near the hose connector and set them aside.
Seat the burner into the housing as the manual shows, and avoid touching the burner or the igniter rod. Align the burner thumbscrews with the threaded holes in the oven and tighten them by hand only. The burner should sit fully in place with no visible gap and no movement.
Solo Stove Pi gas burner specs at a glance
The Solo Stove Pi gas burner, model PIZZA-OVEN-12-BURNER, is rated at 15,000 BTU/hr on propane with 11 inches water column of gas pressure. The table lists the figures printed in the Solo Stove gas burner instruction manual.
| Spec | Value in the manual |
|---|---|
| Model number | PIZZA-OVEN-12-BURNER |
| Heat output | 15,000 BTU/hr |
| Fuel type | Propane only |
| Gas pressure | 11 inches water column (W.C.) |
| Certification | ANSI Z21.89-(2017) / CSA 1.18-(2017) |
| Regulator | Supplied regulator; replacement part PI-REG |
| Country of use | United States and Canada |
The manual warns that any modification, including removing the burner housing tags and labels, voids the appliance’s certification. Leave the tags in place, and check the model number on the label before you order a part.
Propane cylinder and regulator rules
A Solo Stove Pi gas burner setup runs on a propane cylinder of up to 20 lb with a QCC-1 connection, using the regulator supplied with the burner. The manual sets clear limits on the cylinder, its spacing and the regulator.
- Cylinders over 2.2 lb (1.0 kg) need a collar that protects the cylinder valve.
- Never fill a cylinder beyond 80 percent.
- Keep at least 12 inches (31 cm) between the oven and the cylinder.
- Leave 36 inches (92 cm) between the sides and back of the oven and any wall. For the oven’s own footprint, see Solo Stove Pi dimensions.
- Use only the supplied regulator, or Solo Stove part PI-REG as the replacement.
Store cylinders outdoors, out of direct sun, rain and snow, and never under or near the appliance. Keep flammable liquids and any cylinder not connected to the burner at least 25 feet away. Place the dust cap on the cylinder valve whenever the cylinder is not in use.
The manual says installation must follow local codes or, where none apply, the National Fuel Gas Code and the propane installation codes it names. Check with your local fire authority before you connect a cylinder for the first time.
How to light and check the Solo Stove Pi gas burner
To light the Solo Stove Pi gas burner, open the cylinder valve, push the knob in and turn it counter-clockwise until you hear a click. Then look through the front door opening to confirm the flame is lit.

- Confirm the burner knob is fully in the off position.
- Turn the propane cylinder valve on.
- Push the knob in and turn it counter-clockwise until a click sounds.
- If the flame does not catch, turn the knob off, wait 5 minutes and repeat.
- Check that the flame spreads evenly across all burner openings. It should look blue at the base with yellow tips.
- Let the oven heat for 15 minutes at 100 percent, then adjust the knob to reach the interior temperature you want.
- After use, turn the knob and the cylinder valve fully off, and let the oven cool before you handle it.
On the first use, the manual says to run the oven for 30 extra minutes so any factory coatings burn off. The manual recommends a handheld infrared thermometer to read the interior temperature while you adjust the knob.
For a leak check, mix one part liquid dish soap with one part water and brush it onto every fitting. Small bubbles or streams mean a leak. If you find one, close all gas valves, wait 10 minutes, retighten the fittings and test again. Never use an open flame to look for a leak.
The kit includes a match holder that can replace the self-lighting feature. Extend it fully before use, and take extra care when you light a wooden match in the spiral end.
Gas vs wood: what reviewers reported
Gear Patrol’s 2022 review reported that the Solo Stove Pi gas burner reached about 900 F and the wood setup about 850 F, but the reviewer did not describe a test method for either figure.
| Fuel | Reported maximum | Preheat figure |
|---|---|---|
| Propane burner | 900 F (reviewer statement) | About 18 minutes to 800 F |
| Wood | 850 F (reviewer statement) | About 18 minutes to 800 F |
The same article says that with the burner on full blast, the outside of a pizza was scorched in roughly a minute. That is a reported observation, not a measured result, so read it as a rough guide. For oven heat in general, see Solo Stove Pi temperature. You can read the full Gear Patrol Pi oven review for the reviewer’s own wording.
Do not mix fuels. The manual forbids using any other fuel in addition to propane during operation, so the gas burner and a wood fire are separate setups, not a combined cook.
Safety rules for carbon monoxide and gas leaks
The Solo Stove Pi gas burner is for outdoor use only, because its exhaust contains carbon monoxide, an odorless gas that can kill in an enclosed space. The manual is firm on location, supervision and gas handling.
- Use it outdoors in a well-ventilated area, never in a building, garage, tent, camper, car or house.
- Do not use it on a boat or RV, and do not use it as a heater.
- Never run it unattended.
- Keep children and pets away, and do not touch exterior surfaces while it is in use.
- Do not move the appliance while it is running, and lock the stand wheels if you use the stand.
If you smell gas, the manual says to shut off the propane tank valve, shut off the burner knob, put out any open flame and move away from the appliance. If the smell continues, call your fire department immediately.
Cleaning, hose checks and replacement parts
Inspect the hose on the Solo Stove Pi gas burner before every use, and clean the unit only after it has cooled to room temperature.
Check the hose for abrasion, cuts and cracks each time you light the burner. If you find damage, contact Solo Stove Customer Support at 817-900-2664 for a replacement part, as the manual instructs.
Wipe the unit with a clean, lint-free towel that you have sprayed first, rather than spraying the burner directly. Never submerge the burner assembly in water, and do not clean the burner or its orifice with sharp objects.
The pizza stone is fragile. Avoid placing frozen food on a hot stone or spraying cold liquid onto it, and replace a damaged stone only with a genuine Solo Stove part.
Frequently Asked Questions
Does the Solo Stove Pi gas burner run on natural gas?
No. The manual approves the burner for propane only and says not to use any other fuel. It also warns against modifying the valve, igniter or burner, so do not adapt it for another gas.
What is the heat output of the Solo Stove Pi gas burner?
The manual rates the Solo Stove Pi gas burner at 15,000 BTU/hr on propane, with 11 inches water column of gas pressure. The actual oven temperature also depends on the knob setting, so use an infrared thermometer to check it.
What propane cylinder size works with it?
The manual lists cylinders up to 20 lb with a QCC-1 connection. Cylinders over 2.2 lb need a collar to protect the valve, and you should never fill a cylinder beyond 80 percent.
How long does the Solo Stove Pi gas burner take to heat up?
The manual says to heat the oven for 15 minutes at 100 percent before adjusting the knob, and to run it for 30 more minutes on first use. A 2022 review reported about 18 minutes to reach 800 F, which is a reviewer figure, not a manual figure.
Can I use the Solo Stove Pi gas burner indoors or in a garage?
No. The manual says the burner is for outdoor use in a well-ventilated area, because it produces carbon monoxide. Do not use it in a building, garage, tent, camper, car or house.
Can I use a regulator from another brand?
No. The manual requires the regulator supplied with the burner and says to replace it only with Solo Stove part PI-REG. Modifications of any kind void the certification, so stick with the supplied part.
Before your first fire with the Solo Stove Pi gas burner, check the cylinder size, the clearances and the outdoor location against the manual, then run the soap-water leak test. If anything does not match the manual, stop and contact Solo Stove Customer Support before you light the burner. To compare the oven with a rival, read Ooni vs Solo Stove pizza oven, or browse the by use and model guides.
7 min readBy Use & ModelOoni Karu 12 Gas Burner: Complete Fit and Safe Setup GuideUpdated Nov 18, 2026
8 min readBy Use & ModelSolo Stove Pi Prime Manual: Setup, Safety and Care GuideUpdated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Accessories: What Comes With It and What to AddUpdated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Prime Dimensions: Size, Weight and Panoramic OpeningUpdated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Temperature: How Hot It Gets and How to Read ItUpdated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Prime Recipes: Easy Guide for 2026Updated Nov 8, 2026