Solo Stove Pi Temperature: How Hot It Gets and How to Read It
8 min read · by Arjun Mehta · Last updated: November 8, 2026
The solo stove pi temperature range depends on the model, and the Pi Prime propane version reaches up to 900 degrees Fahrenheit, according to Popular Science. The figures in this guide come from 2023 reviews, so they describe the units as tested then.
The Pi Fire attachment runs cooler, with its stone recommended between 500 and 650 degrees Fahrenheit. Confirm which model you own before you plan a bake using the solo stove pi temperature.
Solo Stove Pi Temperature: How Hot Does It Get?
The solo stove pi temperature of the Pi Prime reaches up to 900 degrees Fahrenheit on its removable cordierite stone, the highest figure among the reviews checked for this guide.
Popular Science reports that the Pi Prime cooks 12-inch pizzas at temperatures up to 900 degrees on that stone. Its testers also read over 900 degrees when the burner was cranked, and a pizza came out bubbling from a 750-degree chamber during their test.
Hitting the top setting is not the same as holding it for a whole session. The reviews do not report how long the 900-degree reading lasted under load, so treat the maximum as a ceiling rather than a steady cooking temperature.
The solo stove pi temperature of 900 degrees applies to the propane Pi Prime. The Pi Fire attachment, covered below, is designed for a much lower stone range. For how other gas ovens compare, see this guide to propane pizza oven temperature.
Solo Stove Pi Temperature by Model
Each model has its own heat ceiling, so compare the solo stove pi temperature figure against the model you actually own before you plan a bake.

| Model | Reported temperature | Fuel | Source |
|---|---|---|---|
| Solo Stove Pi Prime | Up to 900 degrees; over 900 when cranked | Liquid propane only | Popular Science review |
| Solo Stove Pi with propane attachment | Up to 900 degrees | Propane | Reviewed comparison |
| Solo Stove Pi Fire | Stone recommended at 500 to 650 degrees; stone maximum about 650 degrees | Wood | Bob Vila review |
The Pi Fire tester also took an infrared reading of the stone and recorded 733 degrees, a figure the article describes as surprisingly high and above the 650-degree stone maximum it cites. Treat that as a single surface reading from one test, not a rated limit.
How Long the Pi Takes to Reach Cooking Temperature
The Pi Prime heats up in under 15 minutes with electric start, but testers waited about 20 minutes before loading the first pizza.
Popular Science says electric start lights the fire instantly and that the oven heats up in less than 15 minutes. The same testers ran it for about 20 minutes before putting in the first pizza, which is a more realistic preheat window for the stone.
On the Pi Fire, Reviewed reports that the stone reached 600 degrees about 30 minutes after lighting, using kindling and three logs of wood. Bob Vila describes the attachment as ready within minutes after the fire starts, and its tester found the stone took about an hour to cool from its peak back down to 650 degrees.
Best Stone Temperatures for Each Crust Style
For the solo stove pi temperature on the Pi Fire, regular crust baked best at 550 to 625 degrees, and thin crust did best at 600 to 660 degrees.

- Regular crust: about 8 minutes in the 550 to 625 degree range
- Thin crust: about 6 minutes in the 600 to 660 degree range
- Manufacturer’s stone range for the Pi Fire: 500 to 650 degrees
These solo stove pi temperature results come from one tester and one oven, so use them as a starting point. For dough and topping ideas, browse these Solo Stove Pi pizza recipes. The reviews do not test other factors such as topping amount, so adjust by eye after your first bake.
How to Measure the Temperature Accurately
The Pi Prime has no built-in thermometer, so an infrared thermometer is the practical way to check the stone to confirm the solo stove pi temperature before you launch a pizza.
Popular Science points out the conspicuous absence of a thermometer on the Pi Prime and calls an infrared thermometer a must for extended cooks. Without one, you are relying on preheat time alone, which the reviews show can vary.
An infrared thermometer reads the surface it points at. Bob Vila’s tester aimed theirs at the stone itself, which is the reading that matters for crust, rather than the air inside the oven.
Why the Stone Temperature Drops When You Add a Pizza
Loading a pizza pulled the Pi Fire stone from 600 degrees down to 440 degrees in the Reviewed test, and the stone was back to 500 degrees about 5 minutes later.
The drop happens as soon as the cold dough touches the stone. Preheat the stone above your target, then launch the pizza once the reading settles back into range, not at the peak. Wipe-down habits matter between bakes too, so see this guide on how to clean a pizza stone.
Fuel also changes how you manage the solo stove pi temperature. Popular Science says the Pi Prime works only with liquid propane, the same type used in a gas grill, while the Pi Fire runs on wood. Check the manual for your model, or read the Solo Stove Pi instructions, before you connect a tank or add logs.
Reading the Stone Temperature on the Pi Fire
The wood-fired Pi Fire is a different case for solo stove pi temperature, because the stone temperature rises and falls with the fire. The manufacturer’s recommended stone range is 500 to 650 degrees Fahrenheit, and Bob Vila’s tester used an infrared thermometer to read the stone at 733 degrees during a test, which is above that stated maximum. Infrared readings depend on the spot you aim at and the surface you measure, so treat a single number as a snapshot, not a setting.
Reviewed’s tester found that the stone reached about 600 degrees roughly 30 minutes after lighting, with wood kindling and three logs. When the pizza went onto the stone, the surface dropped from 600 to 440 degrees, and it was back near 500 degrees by the time the first pizza finished, about 5 minutes later. That drop is why a wood-fired oven needs a short recovery before the next pizza.
- Recommended stone range: 500 to 650 degrees Fahrenheit.
- Stone at about 600 degrees: roughly 30 minutes after lighting, per the Reviewed test.
- Drop when loading one pizza: about 600 to 440 degrees.
- Recovery: back near 500 degrees in about 5 minutes.
Common Temperature Mistakes That Waste a Session
The most common mistake with solo stove pi temperature is trusting the flame or the dome and skipping the stone. The Pi Prime has no built-in thermometer, so the temperature you see on a stand-alone device is the only check you get. Measure the stone itself, not the air above it, and aim at the center of the stone where the pizza sits.
A second mistake is cranking the propane burner to the top setting and assuming the stone will keep pace. Reviewers reported the Pi Prime going over 900 degrees when cranked, but a stone that is still cold in the middle will bake an uneven base. Give the stone the full preheat, then recheck it before each pizza, because a hot stone cools fast when the dough goes on.
Keep the oven’s manual handy for the burner settings and safety clearances, since the temperature range is only useful if the oven runs safely at that setting.
Frequently Asked Questions
What is the highest temperature the Solo Stove Pi Prime reaches?
For the Pi Prime, Popular Science reports a solo stove pi temperature of up to 900 degrees Fahrenheit on its removable cordierite stone. Its testers also read over 900 degrees when the burner was cranked. These are third-party test figures from 2023, so confirm them against the manufacturer’s current specifications.
Does the Solo Stove Pi Prime have a built-in thermometer?
No. Popular Science notes that the Pi Prime has no built-in thermometer. The reviewer recommends an infrared thermometer for extended cooks, so plan to buy one separately if you bake often.
What fuel does the Solo Stove Pi Prime use?
The Pi Prime works only with liquid propane, the same kind used in a gas grill, according to Popular Science. It does not burn wood. Check the manual before you connect a tank to the oven.
How long does the stone take to heat?
On the Pi Prime, the oven heats in under 15 minutes with electric start, and testers waited about 20 minutes before the first pizza. On the Pi Fire, the stone reached 600 degrees about 30 minutes after lighting the wood fire.
Can I rely on the official Solo Stove temperature figures?
Not fully. The manufacturer’s specification page could not be read while preparing this guide, so the numbers here come from third-party reviews published in 2023. Check Solo Stove’s current product page for the model you own before relying on any solo stove pi temperature figure.
Why does a Pi Fire stone read above its 650 degree maximum?
The Bob Vila test read 733 degrees with an infrared thermometer, and infrared readings depend on the spot and surface measured. The manufacturer’s 500 to 650 degree range is the recommended setting, so when you check solo stove pi temperature, treat a higher reading as a sign to let the fire settle.
Choose your model first, since the solo stove pi temperature differs sharply between the propane Pi Prime and the wood-fired Pi Fire. Preheat past your target, then confirm the stone reading with an infrared thermometer before you launch the pizza.
8 min readBy Use & ModelSolo Stove Pi Prime Manual: Setup, Safety and Care GuideUpdated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Prime Dimensions: Size, Weight and Panoramic OpeningUpdated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Prime Recipes: Easy Guide for 2026Updated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Recipes: Official Doughs and Topping IdeasUpdated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Dimensions: Size, Weight and Cooking SurfaceUpdated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Pizza Dough Recipe: Two Official FormulasUpdated Nov 10, 2026