Solo Stove Pi Prime Manual: Setup, Safety and Care Guide
8 min read · by Arjun Mehta · Last updated: November 8, 2026
The Solo Stove Pi Prime manual covers setup, propane lighting, preheating and care for this propane-fired outdoor pizza oven. The booklet packed with the oven is the document to follow, and this guide shows what Solo Stove’s published Pi instructions say so you know what to check.
Solo Stove’s Prime-specific PDF could not be opened for this guide, so the safety distances and lighting steps below come from its published Pi gas burner manual and Pi starter guide. Check every figure against the Solo Stove Pi Prime manual that ships with your oven.
This page is a summary, not a replacement for the manual. Gas appliances can cause fire, explosion or carbon monoxide poisoning when misused.
Where to Find the Solo Stove Pi Prime Manual
The printed Solo Stove Pi Prime manual ships with the oven, and it is the only source that matches your unit’s exact parts and steps. Reviewers who received the Prime list a manual in the box alongside the stones, match holder and weatherproof cover.
The ActiveGearReview Prime review, written by Nazar Kluchkovskiy and published September 14, 2023, gives the main specifications. The review was updated September 1, 2026.
| Feature | Pi Prime (per review) |
|---|---|
| Height | 15.5 in (39.4 cm) |
| Diameter | 20.5 in (52.1 cm) |
| Weight | 30 lb (13.6 kg) |
| Body material | 304 stainless steel |
| Fuel | Propane |
The review’s figures are a useful cross-check for the Solo Stove Pi Prime manual. It gives a recommended cooking temperature of 750 without naming a unit. Solo Stove’s starter guide sets a target of 650°F to 800°F for the stone, so that is the range to use with an infrared thermometer. Our Solo Stove Pi temperature guide goes deeper on heat.
Solo Stove’s gas burner accessory is a separate part for the Pi family, listed under the model number PIZZA-OVEN-12-BURNER. Confirm that number against the Solo Stove Pi Prime manual before you follow its steps, and see the Solo Stove Pi Prime dimensions for sizes.
Gas Burner Safety Rules Before You Light
Use the Solo Stove Pi Prime manual’s gas rules as a checklist: use the gas burner only outdoors, and keep the propane cylinder at least 12 inches from the appliance. The manual also requires 36 inches of clear space at the sides and back.

The Solo Stove gas burner instruction manual warns that carbon monoxide has no odor and can kill. Never use the oven inside a building, garage, tent, camper, car or any enclosed space.
- Keep the oven at least 10 feet from combustible materials.
- Store flammable liquids and any gas cylinder not connected to the oven at least 25 feet away.
- Keep the fuel hose at least 3 inches (8 cm) from any hot surface.
- Do not use the front door with the gas burner, and do not run it in windy conditions.
- Never use an open flame to check for gas leaks.
- Keep the burner and oven away from direct rain or snow.
If you smell gas, shut off the propane tank valve and the burner knob, put out any open flame, and move away from the oven. The manual says to call the fire department if the odor continues.
Connecting the Propane Cylinder Safely
Connect only the regulator supplied with the burner, hand tighten each fitting, and test every connection for leaks before the first burn, as the Solo Stove Pi Prime manual describes.
- Clean out the ash pan, then remove the wood-burning access door, fuel grate and ash pan.
- Inspect the gas burner for damage, seat it in the oven, and hand tighten the thumbscrews. Do not overtighten.
- Check the regulator and cylinder fittings for dirt or damage. If you find any, do not install.
- Align the regulator with the cylinder fitting and hand tighten it. Do not use tools.
- Mix one part liquid dish soap with one part water, coat the fittings, and watch for bubbles. If you find a leak, turn off all gas valves, wait 10 minutes, retighten and test again.
The manual accepts propane cylinders up to 20 lb (9.0 kg) with QCC-1 connections. Cylinders above 2.2 lb (1.0 kg) need a collar to protect the valve, and you should never fill a cylinder beyond 80 percent full.
Lighting, Preheating and the Match Holder
Following the Solo Stove Pi Prime manual, light the gas burner with the knob, let the oven heat for 15 minutes at full power, and give the first use an extra 30 minutes to burn off factory coatings.
- Make sure the burner knob is fully in the off position.
- Open the propane cylinder valve.
- Push the knob in and turn it counterclockwise until you hear a click, then look through the front opening to confirm the flame.
- If the flame does not light, turn the knob off, wait 5 minutes, and repeat.
- Check that the flame is even across the burner openings. It should look blue at the base with yellow tips.
The Solo Stove Pi starter guide says the oven is ready when the stone reaches at least 650°F, and that it can preheat in about 15 minutes after the first use. Measure the center of the stone with an infrared thermometer.
The Solo Stove Pi Prime manual describes the match holder as an alternative to the self-lighting feature. Extend it fully, light a wooden match, turn the knob to the three-quarter position, and insert the match over the burner tube within 5 seconds. If it takes longer, turn the knob off and wait 5 minutes before trying again.
Cooking Temperature and Pizza Stone Care
Following the Solo Stove Pi Prime manual, keep the stone between 650°F and 800°F before you launch a pizza, and avoid placing frozen food or cold liquid on a hot stone.

The stone is cordierite and comes in two halves. It breaks or chips if dropped, so do not use a damaged stone. The Solo Stove Pi Prime manual says a replacement must be a genuine Solo Stove part.
Keep fatty foods and oil off the stone. The manual warns they can cause smoke, odors and fire. If a grease fire starts, shut off the burner knob and the cylinder valve, and do not use water on it.
Cleaning and Routine Maintenance
Clean the gas burner only after it cools to room temperature, using warm soapy water on a clean, lint free towel rather than abrasive pads.
- Wipe the stainless steel in the direction of the brushed grain.
- Never submerge the burner or spray cleaner directly onto it.
- Do not clean the burner or orifice with sharp objects.
- Keep the burner openings and vent locations free of debris and insects.
- Check the igniter pin above the burner tube. A bent pin can stop the burner from lighting.
- Inspect the fuel hose for cuts, abrasion and cracks before each use.
The Solo Stove Pi Prime manual says stainless steel will discolor and patina with heat, and that this is normal. The Prime review adds that some char on the stones is normal after cleaning, and it advises wiping the stones and covering the oven. For the standard model, read the Solo Stove Pi instructions.
What to Do When the Flame Goes Out
Turn the burner off first, then follow the Solo Stove Pi Prime manual’s step for your situation, and do not use the oven until the problem is cleared.
| Situation | What the manual says |
|---|---|
| Burner does not light | Turn the knob off, wait 5 minutes, then repeat the lighting steps. |
| Flame goes out during use | Turn the knob off, then the cylinder valve, and wait at least 5 minutes before relighting or changing the cylinder. |
| Hose is damaged | Do not use it. Contact Solo Stove Customer Support at 817-900-2664 for a replacement part. |
| Gas smell | Shut off the propane valve and the knob, put out open flames, and call the fire department if the odor continues. |
Frequently Asked Questions
Where can I find the Solo Stove Pi Prime manual?
The manual ships with the oven and is the document to follow. Solo Stove also hosts its Pi gas burner instruction PDF on its own store files. The Prime-specific PDF could not be opened for this guide, so check every figure against your own booklet.
Can I use butane instead of propane?
No. The gas burner manual says to use only propane, and it warns against any other fuel. Use the regulator supplied with the burner, and check the manual before changing anything about the fuel.
Can I use the Pi Prime indoors?
No. The solo stove pi prime manual says the oven is for outdoor use only because combustion produces carbon monoxide. Do not use it in a building, garage, tent, camper, car or other enclosed area.
How long does it take to preheat?
The starter guide says the first burn should run at least 30 minutes, and later burns can preheat in about 15 minutes. Aim for a stone temperature of at least 650°F before you launch a pizza, and check the Solo Stove Pi Prime manual that came with your oven for its own preheat advice.
Can I leave the oven unattended while the burner is on?
No. The Solo Stove Pi Prime manual says never to operate the appliance unattended. The oven stays hot during use and afterwards, so let it cool completely before handling it.
Read the Solo Stove Pi Prime manual that ships with your oven before you light it, and keep it near the oven for reference. If the flame, the hose or the cylinder fittings look wrong, shut the gas off and wait until the problem is fixed. This guide summarizes Solo Stove’s published Pi instructions and does not replace them. When you are ready to cook, try the Solo Stove Pi Prime recipes.
8 min readBy Use & ModelSolo Stove Pi Prime Recipes: Easy Guide for 2026Updated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Prime Dimensions: Size, Weight and Panoramic OpeningUpdated Nov 8, 2026
6 min readBy Use & ModelSolo Stove Pi Prime Accessories: What Each One Is ForUpdated Nov 15, 2026
9 min readBy Use & ModelSolo Stove Pi Gas Burner: Specs, Propane Setup and Safe UseUpdated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Temperature: How Hot It Gets and How to Read ItUpdated Nov 8, 2026
8 min readBy Use & ModelSolo Stove Pi Recipes: Official Doughs and Topping IdeasUpdated Nov 8, 2026